Material data sheets

Material Data Sheets

64 documents AFS has on file today: certifications, tested ratings, method sheets, standards and data. Add any of them to a submittal package.

Build a submittal package Request a document

Tested systems (ES-1)

9 ON FILE

Only the Drexel Metals ES-1 systems listed here, fabricated by AFS under the Drexel certification program from Drexel-supplied material, carry Drexel's published ES-1 ratings. A non-Drexel or custom fabricated AFS component does not carry that tested rating, or the tested performance of any independently tested proprietary assembly.

Drexel Metals Snap Coping-Max

Drexel Metals

Published ratings (2)

24 gauge cover, face up to 12 in, wall up to 32 in: -75 psf sustained (Drexel published test value)
.040 AL cover, face up to 12 in, wall up to 32 in: -75 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Snap Coping-Max as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Snap Coping-Max-C

Drexel Metals

Published ratings (3)

24 gauge cover, face up to 12 in, wall up to 24 in: -170 psf sustained (Drexel published test value)
.040 AL cover, face up to 12 in, wall up to 24 in: -180 psf sustained (Drexel published test value)
.050 AL cover, face up to 12 in, wall up to 32 in: -155 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Snap Coping-Max-C as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Econo Coping LT

Drexel Metals

Published ratings (4)

24 gauge cover, face up to 6 in, wall up to 16 in, 24 ga cleat: -110 psf sustained (Drexel published test value)
24 gauge cover, face up to 6 in, wall up to 20 in, 24 ga cleat: -85 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, wall up to 16 in, 24 ga cleat: -115 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, wall up to 20 in, 24 ga cleat: -85 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Econo Coping LT as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Econo Coping

Drexel Metals

Published ratings (4)

24 gauge cover, face up to 6 in, wall up to 16 in, 22 ga cleat: -110 psf sustained (Drexel published test value)
24 gauge cover, face up to 6 in, wall up to 20 in, 22 ga cleat: -75 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, wall up to 16 in, 22 ga cleat: -145 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, wall up to 20 in, 22 ga cleat: -65 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Econo Coping as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Fascia LT

Drexel Metals

Published ratings (2)

24 gauge cover, face up to 8 in, 22 ga cleat: -210 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, 22 ga cleat: -180 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Fascia LT as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Gravel Stop

Drexel Metals

Published ratings (2)

24 gauge cover, face up to 10 in, 22 ga cleat: -140 psf sustained (Drexel published test value)
.040 AL cover, face up to 10 in, 22 ga cleat: -130 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Gravel Stop as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Econo Gravel Stop

Drexel Metals

Published ratings (2)

24 gauge cover, face up to 7 in, 24 ga cleat: -70 psf sustained (Drexel published test value)
.040 AL cover, face up to 7 in, 24 ga cleat: -90 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Econo Gravel Stop as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Drip Edge LT

Drexel Metals

Published ratings (2)

24 gauge cover, face up to 6 in, 24 ga cleat: -240 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, 24 ga cleat: -250 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Drip Edge LT as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Drexel Metals Drip Edge

Drexel Metals

Published ratings (2)

24 gauge cover, face up to 6 in, 22 ga cleat: -175 psf sustained (Drexel published test value)
.040 AL cover, face up to 6 in, 22 ga cleat: -185 psf sustained (Drexel published test value)

Design Engineer must apply the Factor of Safety.
Applies only to Drexel Metals ES-1 rated perimeter edge systems and GT-1 rated gutter systems.
Authorized after a third-party quality-control audit, per shop location; certification is good for one year.
All material must be purchased through Drexel Metals: painted sheets for cover and splice, galvanized sheets for cleats, and fasteners/nails. Cleats are pre-punched with properly spaced holes and secured with Drexel-provided fasteners.
Applies only to the Drip Edge as published by Drexel. A non-Drexel or custom profile does not carry this rating.

View Add to submittal

Need something that isn't listed?

Ask AFS for mill certificates, warranty terms or a project-specific document. We reply by email.